Book a Demo!
CoCalc Logo Icon
StoreFeaturesDocsShareSupportNewsAboutPoliciesSign UpSign In
nu11secur1ty
GitHub Repository: nu11secur1ty/Kali-Linux
 Path: blob/master/ALFA-W1F1/RTL8814AU/include/Hal8812PwrSeq.h
1307 views
1
/******************************************************************************

2
 *

3
 * Copyright(c) 2007 - 2017 Realtek Corporation.

4
 *

5
 * This program is free software; you can redistribute it and/or modify it

6
 * under the terms of version 2 of the GNU General Public License as

7
 * published by the Free Software Foundation.

8
 *

9
 * This program is distributed in the hope that it will be useful, but WITHOUT

10
 * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or

11
 * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for

12
 * more details.

13
 *

14
 *****************************************************************************/

15


16


17
#ifndef __HAL8812PWRSEQ_H__

18
#define __HAL8812PWRSEQ_H__

19


20
#include "HalPwrSeqCmd.h"

21


22
/*

23
	Check document WB-110628-DZ-RTL8195 (Jaguar) Power Architecture-R04.pdf

24
	There are 6 HW Power States:

25
	0: POFF--Power Off

26
	1: PDN--Power Down

27
	2: CARDEMU--Card Emulation

28
	3: ACT--Active Mode

29
	4: LPS--Low Power State

30
	5: SUS--Suspend

31


32
	The transision from different states are defined below

33
	TRANS_CARDEMU_TO_ACT

34
	TRANS_ACT_TO_CARDEMU

35
	TRANS_CARDEMU_TO_SUS

36
	TRANS_SUS_TO_CARDEMU

37
	TRANS_CARDEMU_TO_PDN

38
	TRANS_ACT_TO_LPS

39
	TRANS_LPS_TO_ACT

40


41
	TRANS_END

42
*/

43
#define	RTL8812_TRANS_CARDEMU_TO_ACT_STEPS	15

44
#define	RTL8812_TRANS_ACT_TO_CARDEMU_STEPS	15

45
#define	RTL8812_TRANS_CARDEMU_TO_SUS_STEPS	15

46
#define	RTL8812_TRANS_SUS_TO_CARDEMU_STEPS	15

47
#define	RTL8812_TRANS_CARDEMU_TO_PDN_STEPS	15

48
#define	RTL8812_TRANS_PDN_TO_CARDEMU_STEPS	15

49
#define	RTL8812_TRANS_ACT_TO_LPS_STEPS	15

50
#define	RTL8812_TRANS_LPS_TO_ACT_STEPS	15

51
#define	RTL8812_TRANS_END_STEPS	1

52


53


54
#define RTL8812_TRANS_CARDEMU_TO_ACT														\

55
	/* format */																\

56
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\

57
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT2, 0},/* disable SW LPS 0x04[10]=0*/	\

58
	{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT1, BIT1},/* wait till 0x04[17] = 1    power ready*/	\

59
	/*{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0}, disable HWPDN 0x04[15]=0*/ \

60
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3, 0},/* disable WL suspend*/	\

61
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/* polling until return 0*/	\

62
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT0, 0},/**/   \

63
	{0x0024, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0}, /* 0x24[1] Choose the type of buffer after xosc: nand*/   \

64
	{0x0028, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3, 0}, /* 0x28[33] Choose the type of buffer after xosc: nand*/

65


66
#define RTL8812_TRANS_ACT_TO_CARDEMU													\

67
	/* format */																\

68
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\

69
	{0x0c00, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x04}, /* 0xc00[7:0] = 4	turn off 3-wire */	\

70
	{0x0e00, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x04}, /* 0xe00[7:0] = 4	turn off 3-wire */	\

71
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0}, /* 0x2[0] = 0	 RESET BB, CLOSE RF */	\

72
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/	\

73
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},  /* Whole BB is reset*/			\

74
	/*{0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0},//0x1F[7:0] = 0 turn off RF*/	\

75
	/*{0x004E, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0},//0x4C[23] = 0x4E[7] = 0, switch DPDT_SEL_P output from register 0x65[2] */	\

76
	{0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x2A}, /* 0x07[7:0] = 0x28 sps pwm mode 0x2a for BT coex*/	\

77
	{0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x02, 0},/*0x8[1] = 0 ANA clk = 500k */	\

78
	/*{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0 | BIT1, 0}, //  0x02[1:0] = 0	reset BB */	\

79
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1}, /*0x04[9] = 1 turn off MAC by HW state machine*/	\

80
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT1, 0}, /*wait till 0x04[9] = 0 polling until return 0 to disable*/

81


82
#define RTL8812_TRANS_CARDEMU_TO_SUS													\

83
	/* format */								\

84
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\

85
	{0x0042, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xF0, 0xcc},\

86
	{0x0042, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xF0, 0xEC},\

87
	{0x0043, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x07},/* gpio11 input mode, gpio10~8 output mode */	\

88
	{0x0045, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00},/* gpio 0~7 output same value as input ?? */	\

89
	{0x0046, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xff},/* gpio0~7 output mode */	\

90
	{0x0047, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0},/* 0x47[7:0] = 00 gpio mode */	\

91
	{0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0},/* suspend option all off */	\

92
	{0x0014, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x80, BIT7},/*0x14[7] = 1 turn on ZCD */	\

93
	{0x0015, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x01, BIT0},/* 0x15[0] =1 trun on ZCD */	\

94
	{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x10, BIT4},/*0x23[4] = 1 hpon LDO sleep mode */	\

95
	{0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x02, 0},/*0x8[1] = 0 ANA clk = 500k */	\

96
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3, BIT3}, /*0x04[11] = 2b'11 enable WL suspend for PCIe*/

97


98
#define RTL8812_TRANS_SUS_TO_CARDEMU													\

99
	/* format */								\

100
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\

101
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3, 0}, /*0x04[11] = 2b'01enable WL suspend*/   \

102
	{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x10, 0},/*0x23[4] = 0 hpon LDO sleep mode leave */	\

103
	{0x0015, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x01, 0},/* 0x15[0] =0 trun off ZCD */	\

104
	{0x0014, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x80, 0},/*0x14[7] = 0 turn off ZCD */	\

105
	{0x0046, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00},/* gpio0~7 input mode */	\

106
	{0x0043, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00},/* gpio11 input mode, gpio10~8 input mode */

107


108
#define RTL8812_TRANS_CARDEMU_TO_CARDDIS													\

109
	/* format */																\

110
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\

111
	/**{0x0194, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0}, //0x194[0]=0 , disable 32K clock*/	\

112
	/**{0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x94}, //0x93 = 0x94 , 90[30] =0 enable 500k ANA clock .switch clock from 12M to 500K , 90 [26] =0 disable EEprom loader clock*/	\

113
	{0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT2, 0}, /*0x03[2] = 0, reset 8051*/	\

114
	{0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x05}, /*0x80 = 05h if reload fw, fill the default value of host_CPU handshake field*/	\

115
	{0x0042, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xF0, 0xcc},\

116
	{0x0042, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xF0, 0xEC},\

117
	{0x0043, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x07},/* gpio11 input mode, gpio10~8 output mode */	\

118
	{0x0045, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00},/* gpio 0~7 output same value as input ?? */	\

119
	{0x0046, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xff},/* gpio0~7 output mode */	\

120
	{0x0047, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0},/* 0x47[7:0] = 00 gpio mode */	\

121
	{0x0014, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x80, BIT7},/*0x14[7] = 1 turn on ZCD */	\

122
	{0x0015, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x01, BIT0},/* 0x15[0] =1 trun on ZCD */	\

123
	{0x0012, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x01, 0},/*0x12[0] = 0 force PFM mode */	\

124
	{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x10, BIT4},/*0x23[4] = 1 hpon LDO sleep mode */	\

125
	{0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x02, 0},/*0x8[1] = 0 ANA clk = 500k */	\

126
	{0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07 = 0x20 , SOP option to disable BG/MB*/	\

127
	{0x001f, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0}, /*0x01f[1]=0 , disable RFC_0  control  REG_RF_CTRL_8812 */	\

128
	{0x0076, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0}, /*0x076[1]=0 , disable RFC_1  control REG_OPT_CTRL_8812 +2 */	\

129
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3, BIT3}, /*0x04[11] = 2b'01 enable WL suspend*/

130


131
#define RTL8812_TRANS_CARDDIS_TO_CARDEMU													\

132
	/* format */																\

133
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                       \

134
	{0x0012, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/*0x12[0] = 1 force PWM mode */	\

135
	{0x0014, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x80, 0},/*0x14[7] = 0 turn off ZCD */	\

136
	{0x0015, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x01, 0},/* 0x15[0] =0 trun off ZCD */	\

137
	{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x10, 0},/*0x23[4] = 0 hpon LDO leave sleep mode */	\

138
	{0x0046, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00},/* gpio0~7 input mode */	\

139
	{0x0043, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00},/* gpio11 input mode, gpio10~8 input mode */ \

140
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT2, 0}, /*0x04[10] = 0, enable SW LPS PCIE only*/	\

141
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3, 0}, /*0x04[11] = 2b'01enable WL suspend*/	\

142
	{0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT2, BIT2}, /*0x03[2] = 1, enable 8051*/	\

143
	{0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0},/*PCIe DMA start*/  \

144
	{0x0024, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1}, /* 0x24[1] Choose the type of buffer after xosc: schmitt trigger*/ \

145
	{0x0028, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3, BIT3}, /* 0x28[33] Choose the type of buffer after xosc: schmitt trigger*/

146


147


148
#define RTL8812_TRANS_CARDEMU_TO_PDN												\

149
	/* format */																\

150
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/	\

151
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, BIT7},/* 0x04[15] = 1*/

152


153
#define RTL8812_TRANS_PDN_TO_CARDEMU												\

154
	/* format */																\

155
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/	\

156
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0},/* 0x04[15] = 0*/

157


158
#define RTL8812_TRANS_ACT_TO_LPS														\

159
	/* format */																\

160
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\

161
	{0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF},/*PCIe DMA stop*/	\

162
	{0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x7F},/*Tx Pause*/		\

163
	{0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/	\

164
	{0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/	\

165
	{0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/	\

166
	{0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/	\

167
	{0x0c00, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x04}, /* 0xc00[7:0] = 4	turn off 3-wire */	\

168
	{0x0e00, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x04}, /* 0xe00[7:0] = 4	turn off 3-wire */	\

169
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled, and clock are gated, and RF closed*/	\

170
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/	\

171
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},  /* Whole BB is reset*/			\

172
	{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x03},/*Reset MAC TRX*/			\

173
	{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},/*check if removed later*/		\

174
	{0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT5, BIT5},/*Respond TxOK to scheduler*/

175


176


177
#define RTL8812_TRANS_LPS_TO_ACT															\

178
	/* format */																\

179
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/	\

180
	{0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, 0xFF, 0x84}, /*SDIO RPWM*/	\

181
	{0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84}, /*USB RPWM*/	\

182
	{0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84}, /*PCIe RPWM*/	\

183
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/	\

184
	{0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0}, /*.	0x08[4] = 0		 switch TSF to 40M*/	\

185
	{0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT7, 0}, /*Polling 0x109[7]=0  TSF in 40M*/			\

186
	{0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT6 | BIT7, 0}, /*.	0x29[7:6] = 2b'00	 enable BB clock*/	\

187
	{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1}, /*.	0x101[1] = 1*/					\

188
	{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF}, /*.	0x100[7:0] = 0xFF	 enable WMAC TRX*/	\

189
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1 | BIT0, BIT1 | BIT0}, /*.	0x02[1:0] = 2b'11	 enable BB macro*/	\

190
	{0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, /*.	0x522 = 0*/

191


192
#define RTL8812_TRANS_END																\

193
	/* format */																\

194
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/		\

195
	{0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, 0, PWR_CMD_END, 0, 0},

196


197


198
extern WLAN_PWR_CFG rtl8812_power_on_flow[RTL8812_TRANS_CARDEMU_TO_ACT_STEPS + RTL8812_TRANS_END_STEPS];

199
extern WLAN_PWR_CFG rtl8812_radio_off_flow[RTL8812_TRANS_ACT_TO_CARDEMU_STEPS + RTL8812_TRANS_END_STEPS];

200
extern WLAN_PWR_CFG rtl8812_card_disable_flow[RTL8812_TRANS_ACT_TO_CARDEMU_STEPS + RTL8812_TRANS_CARDEMU_TO_PDN_STEPS + RTL8812_TRANS_END_STEPS];

201
extern WLAN_PWR_CFG rtl8812_card_enable_flow[RTL8812_TRANS_ACT_TO_CARDEMU_STEPS + RTL8812_TRANS_CARDEMU_TO_PDN_STEPS + RTL8812_TRANS_END_STEPS];

202
extern WLAN_PWR_CFG rtl8812_suspend_flow[RTL8812_TRANS_ACT_TO_CARDEMU_STEPS + RTL8812_TRANS_CARDEMU_TO_SUS_STEPS + RTL8812_TRANS_END_STEPS];

203
extern WLAN_PWR_CFG rtl8812_resume_flow[RTL8812_TRANS_ACT_TO_CARDEMU_STEPS + RTL8812_TRANS_CARDEMU_TO_SUS_STEPS + RTL8812_TRANS_END_STEPS];

204
extern WLAN_PWR_CFG rtl8812_hwpdn_flow[RTL8812_TRANS_ACT_TO_CARDEMU_STEPS + RTL8812_TRANS_CARDEMU_TO_PDN_STEPS + RTL8812_TRANS_END_STEPS];

205
extern WLAN_PWR_CFG rtl8812_enter_lps_flow[RTL8812_TRANS_ACT_TO_LPS_STEPS + RTL8812_TRANS_END_STEPS];

206
extern WLAN_PWR_CFG rtl8812_leave_lps_flow[RTL8812_TRANS_LPS_TO_ACT_STEPS + RTL8812_TRANS_END_STEPS];

207


208
#endif /* __HAL8812PWRSEQ_H__ */

209


210